When you are away from computer components, simple press the reset button and you are ready to power up again. 2.Why do I have no power at the tip when I am pressing the power switch forward but the red LED is on The power switch goes through a lot.Autel PS100 PowerScan Autel PowerScan PS100 Automotive Circuit Tester Circuit Tester.Autel PS100 PowerScan Circuit Tester for reducing diagnostic time in all 6- to 30-volt vehicle electrical systems.Power Scan PS100 Power Probe Circuit Tester package with Cigarette lighter adapter and PowerScan PS100 Users Manual.
Featuring AVOmeter, test light, built-in flashlight, short circuit indicator, relaycomponent tester, continuity tester and bad ground indicator, the PowerScan is truly the ultimate in power and affordability, allowing users to check circuitry in one single step. An absolute must for every technician looking for a fast and accurate solution to electrical system diagnostics. Autel PowerScan PS100 Automotive Circuit Tester Description: Autel PowerScan PS100 is the best electrical tester for reducing diagnostic time in all 6- to 30-volt vehicle electrical systems. After a simple hook-up of the tool to the vehicles battery, you can: 1.Determine at a glance if a circuit is positive, negative, or open without having to reconnect clips from one battery pole to another. Test for continuity with its built-in auxiliary ground lead. By depressing the power switch, conduct a positive or negative battery current to the probe tip for testing the function of an electrical component without the use of jumper wires. Test for poor ground contacts instantly without performing voltage drop tests. The tool is also short-circuit protected; its internal circuit breaker will trip if it becomes overloaded. Follow and locate short circuits without wasting fuses. The tools long cable allows you to test along the entire length of the vehicle without constantly searching for suitable vehicle grounds. Simultaneously uses the hot lead and the ground lead to activate components right in your hand Instantly identifies positive, negative and open circuits Tests for bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses Instantly checks continuity of switches, relays and diodes Circuit breaker protected Built-in Flashlight enables you to work in the dark Audio tone indicator allows for no-look menu scrolling once users are familiar with menu tone assignment 20ft (extendable) cable provides excellent accessibility to test along the vehicle Extremely easy to use and highly reliable Autel PowerScan PS100 Electrical System Tester Description. Head Lights Illuminates dark work areas or work areas at night.. RedGreen Polarity IndicatorIdentifies positive, negative or open circuits. The RED Indicator lights when the Probe Tip is contacting a positive circuit. The GREEN Indicator lights when the Probe Tip is contacting a negative circuit. Circuit Breaker Reset Resets the tool when the Circuit Breaker is tripped Power SwitchAllows you to conduct a positive or negative battery current to the tip for activating and testing the function of electrical components. Mode ButtonSelects the work mode:AC voltage,DC voltage, resistance, tone. Adaptor Connects to the battery Autel PowerScan PS10 Work Mode: There are four modes to diagnose the electrical systems, which can be accessed by depressing the Mode Button and cycling through each one. AC Voltage While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the Max. Resistance While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead. Tone OnOff While the tool in this mode, just do a quick press of the mode button to toggle the tone on or off. While quickly pressing (a quick press and release) the mode button, if a short high beep is heard, this means the audio tone is turned on. This function is invaluable when working in bright areas where LED illumination alone is not sufficient. The audio feature may be disengaged when desired, such as for applications where the tool will be connected to circuits for long periods of time and the audio could become annoying. Autel Ps100 Vs Power Probe 4 Full Battery CurrentWhen you press the switch forward, you are conducting full battery current to the tip of the probe. Simply connect the extra ground lead to the tool and press the power switch forward until it trips the circuit breaker.This will prevent power from going to the tip but still allow you to use the tool as a multimeter. When you are away from computer components, simple press the reset button and you are ready to power up again. Why do I have no power at the tip when I am pressing the power switch forward but the red LED is on The power switch goes through a lot.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |